[ [ [ Precautions when ordering ] ] ]
This product is a model for external DC power supply only.
You must have an external DC power supply that meets the specifications of this product.
Our recommended external DC power supply product is "LTPW01".
"LTPW01" does not include DC cable and AC cable.
Please purchase them as an option.
We will ship your order approximately 12 days after your order is confirmed.
[ Product Overview ]
A master clock for high-end audio that emphasizes price, combining the technology and experience of cyber shafts. Equipped with ultra-high precision OCXO and specialized in single output, the price has been reduced while maintaining high performance. In addition to being dedicated to an external DC power supply, it is equipped with an ultra-low noise, ultra-high PSRR regulator circuit equipped with two next-generation linear regulator LT3045.
Ultra low phase noise -111dBc / Hz ~ -119dBc / Hz (@ offset 1Hz) OP11 ~ OP19 grades are available.
* The external DC power supply is sold separately from the Palladium main unit.
[ Features ]
This product uses a brand new OCXO, and a unit with outstanding stability is selected and mounted by long-term calibration.
In addition to the OCXO unit, a robust heat insulating case consisting of a magnetic shield plate and a heat shield board is added to maintain an environment where the performance of OCXO can be maximized.
It is designed to be the most compact and high-performance cyber shaft clock product.
Uses aluminum die-cast 3-point support feet that can be stable on any installation surface. It is also possible to replace it with an optional spike insulator with a 4 mm screw.
The output can be set to an impedance of 50Ω or 75Ω. (Registered utility model)
The function to insulate the GND side of the clock output from the GND of the main unit is the best way to protect against external noise. In most cases, insulating the GND will provide a noise-free connection and good results.
You can set whether to connect the output GND potential to the main unit GND or to isolate it. (Registered utility model) It is possible to deal with complicated GND processing that differs for each audio system in detail.
The DC supplied from the external DC power supply regulates the LT3045 with ultra-low noise and ultra-high PSRR inside this unit with a two-unit structure. A truly clean DC is supplied to the OCXO.
For the internal substrate, a copper foil substrate with a thickness of 70 μm, which is twice the normal thickness, is used. The internal layout, which has been verified many times, is in the best condition.
Equipped with an LED monitor that can control the OCXO unit temperature by operating the oven circuit normally.
Strictly measure characteristics using a highly accurate calibrated measuring instrument. The clock quality is guaranteed by plotting the phase noise and allan variance in the output section for each unit.
It comes with a 2-year free repair warranty.
[ Ultra-low noise, ultra-high PSRR linear power regulator ]
Equipped with a two-unit structure regulator circuit that maximizes the performance of the new-generation linear regulator LT3045
The DC input from the external DC terminal is regulated to 12V by a circuit that can obtain a very high PSRR by distributing the current using two LT3045s in parallel, and a clean DC is supplied to the OCXO.
Note) PSRR (Power Supply Rejection Ratio) The power supply voltage fluctuation elimination ratio. Ability to remove power ripple if the input power has power ripple.
[ Output impedance 50Ω / 75Ω switching function ]
The impedance of the external 10MHz clock input of the audio equipment is divided into 50Ω or 75Ω products. In measuring equipment, 50Ω is common, but in audio equipment, the input impedance of the word clock is 75Ω, so the input of external 10MHz is also 75Ω in many cases. Impedance matching is effective in preventing the generation of reflected waves, so it is best to match the impedance of the external clock input of your audio equipment.
For our clock products, the clock output impedance can be set to 75Ω / 50Ω according to the device you are using with a switch. (Registered utility model)
Even if your audio equipment changes in the future, impedance matching of the external 10MHz clock can be reliably supported.
[ Output GND insulation / enclosure GND selection function ]
The output GND potential can be switched between "insulated from the chassis GND" and "housing GND". If the output GND of this unit is grounded in common, the GND potential difference between this unit and the connected device will flow through the GND of the connection cable, causing noise called a GND loop. Therefore, it is usually better to insulate the GND of each output for better noise resistance. Depending on the system you are using, the GND of each device may be firmly grounded. If there is no GND potential difference between these devices, it may be better to have the output GND grounded to the chassis GND to obtain better results against noise.
Since the environment of the audio system is various, you can choose the most suitable method according to your own environment.
[ About supply of external DC power supply ]
This unit is designed to operate only with an external DC power supply. Be sure to prepare an external DC power supply. We also offer low-priced linear power supplies and AC adapter (transformer type) power supplies that can be selected according to your budget. Please see the options section at the bottom of the site.
The specifications of the external DC are 13.5V to 16V 0.8A. The recommended voltage is 14V. The LT3045 can sufficiently eliminate noise even if the input / output voltage difference is 1V. The smaller the input / output voltage difference is within the specified range, the more the LT3045's capabilities can be demonstrated. Therefore, a good DC power supply with very no noise can operate from 13.5V.
The external DC plug standard is 2.1 mm / 5.5 mm. You can use a regular DC plug, but it uses a screwable jack. [RS product 487-820]
[ Palladium OP grade OCXO characteristic selection value ]
The OCXO installed in this product uses a stable individual after several months of calibration of a new OCXO unit. In order to perform the optimum selection as a clock for audio, we perform a comprehensive evaluation of the phase noise characteristics and the short-term stability (Allan variance) that can be scrutinized more closely.
The product cannot be evaluated by measuring only the output characteristics of the built-in OCXO unit. Our calibration measurement is not directly measured from the output of the OCXO unit, but from the output terminal of this product in order to evaluate all the performance including the buffer circuit.
-Selection reference value Products have different options depending on the phase noise characteristics.
[ Selection characteristic value ]
|OP GRADE||Phase Noise @ offset 1Hz / 10Hz||Allan Deviation tau=1sec|
|OP19||> -119 dBc/Hz / -140 dBc/Hz||> 3.0E-13 (0.00030ppb/s)|
|OP18||> -118 dBc/Hz / -140 dBc/Hz||> 3.4E-13 (0.00034ppb/s)|
|OP17||> -118 dBc/Hz / -135 dBc/Hz||> 3.8E-13 (0.00038ppb/s)|
|OP16||> -118 dBc/Hz / -130 dBc/Hz||> 4.2E-13 (0.00042ppb/s)|
|OP15||> -118 dBc/Hz / -130 dBc/Hz||> 4.6E-13 (0.00046ppb/s)|
|OP14||> -118 dBc/Hz / -130 dBc/Hz||> 5.1E-13 (0.00051ppb/s)|
|OP13||> -118 dBc/Hz / -130 dBc/Hz||> 5.6E-13 (0.00056ppb/s)|
|OP12||> -118 dBc/Hz / -130 dBc/Hz||> 6.0E-13 (0.00060ppb/s)|
|OP11||> -118 dBc/Hz / -130 dBc/Hz||> 6.5E-13 (0.00065ppb/s)|
The above values are guaranteed values measured individually, not general catalog values (Typical), so the quality of the product is constant.
* For the phase noise offset of 1Hz, an appropriate value with an offset of 1.000Hz to 1.099Hz is used to avoid averaging errors. Measuring phase noise is very sensitive and has instrumental and measurement errors. The indicated phase noise values include measurement errors, not absolute values. The indicated phase noise value is a value measured under the same conditions of our company and is an index of product grade classification.
[ OP grade guarantee card ]
An "OP grade certificate" with hologram is always attached to each OP grade product.
A tamperproof sticker is attached in the center. A hologram is printed on the right edge. In addition, a hologram sheet with the serial number described in the option grade certificate will be attached to the OCXO unit inside the main unit. Please be sure to check when purchasing for second use.
[ Compatible audio products ]
ESOTERIC Grandioso K1X、K1、P1X、P1X、P1、D1X、D1、K-01XD、K-01Xs、K-01X、K-01、K-03XD、K-03Xs、K-03X、K-03、K-05Xs、K-05X、K-05、K-07Xs、K-07X、K-07、D-02X、D-02、D-05X、D-07X、P-021、P-02X、、N-01XD、N-01、N-03T、N-05、G-0、G-0s、G-0Rb、G-02、G-03X、G-25U、TASCAM CG1000 / dCS Vivaldi clock、Paganini clock、Scarlatti Clock / MUTEC iCLOCK、MC-3+、MC-3+USB / Antelope Audio Isochrone OCX HD、OCX-V、OCX、TRINITY、PURE2、ZODIAC PLATINUM / BRAINSTORM DCD-8 / Phaseteck HD-7A / Phasemation HD-7A192 / SFORZATO DSP-Vera、DSP-Dorado、DSP-Pavo、DSC-Vera、DSC-Drado、DSC-Grus、DSP-01、DST-01、DSP-03、DSP-05 / TEAC UD-503、UD-505、NT-503、NT-505 / SPEC RMP-X1 / Sound Warrior SWD-CL10 / TechDAS D-7、D7i / RATOC RAL-DSDHA2 / M2TECH EVO DAC TWO PLUS、HIFACE EVO TWO / CH Precision C1,D1 / aurender W20/ soulnote D-2、S-3 / SOtM sMS-200ultra、tX-USBultra、SOtM sNH-10G (require master clock input function) /SHENZHENAUDIO GUSTARD U16、Singher SU-2 / iFi Audio Pro iDSD / UpTone Audio EtherREGEN / Audio Gd DI-20HE、DI-20、R-7HE (version 2020)、R-7 (version 2020) /VMV SMSL D3
Other, master clock generator with 10MHz clock input, CDP, DDC, DAC, Audio HUB, etc.
*If you are uncertain about the specifications of the device you are using, please contact us with the model name.
[ Specification ]
Accessories: instruction manual, test report, and phase noise/Alan dispersion characteristic graph
BNC cable is not included.
Output: 10 MHz x 1 lines, sine wave
Output level: 1.5 Vp-p ( with 50 ohm setting)
Output impedance: 50 ohms/75 ohms Each system is individually switchable
Output GND potential: Main body GND/insulation can be switched (each system can be switched independently)
Body size: W110mm x D212mm x H70mm (including protrusions) Optional Spike insurator use H78mm
Weight approx. 1 kg
External DC power supply: DC 13.5V-16V 1A recommended voltage 14V
External DC plug standard: 2.1 mm/5.5 mm screwable
○ 2-year free repair guarantee
*Design and specifications are subject to change without notice for improvement.